Build a Dock using Pipe Hardware as seen on Maine Cabin Masters
Slide mouse over the interactive dock graphics then click to expand or add to cart.
The above floating dock connected to stationary dock is only recommended in calm locations.
In windy locations up to 6′ deep, stationary docks work better for allowing waves to pass under.
Our products are either shipped UPS Ground, Freight, or LTL. We do not know which shipping method would be least expensive, until we review the parts ordered and their quantity. If you wish, you can contact a customer service representative for an accurate total (including shipping) and from there the order can be placed. Though this process takes more time, it is done to ensure absolute accuracy. We appreciate your business, and we strive to make every sale as efficient as possible. Thank you!
Click products for more details or purchase pipe dock hardware below
Corner Socket #4050
Bolts to a wood dock frame and fits 1 7/8″ OD Pipe. (Schedule 40 Galvanized Pipe) Flip upside down for opposite side of dock. To avoid confusion when buying pipe that fits in this, the industry standard calls the pipe … Read More
Pipe Bracket (2 Pack) #4071
Dock Pipe Bracket bolts to the 2×6 dock frame and has set screws for height adjustment on 1.5″ schedule 40 pipe leg.
Flush Mount Pipe Bracket #4183
Marine Grade Aluminum
Requires four 3/8″ carriage bolts
Fits 1.5″ schedule 40 Pipe
Pipe Foot (2 Pack) #4180
Dock Pipe Leg Foot with a set screw for vertical adjustment. Pipe can pass through the foot into the ground while the foot prevents the leg from pushing deeper when weight is added. Dock feet are not always needed on rocky lake bottoms but more commonly used on mud and sand. Foot plate size is 9.5″ x 9.5″
Corner Pipe Bracket #4059
Marine grade aluminum
Use two 3/8″ carriage bolts.
4.5″ tall
J Bracket Connector #9067
Connect stationary dock sections with these brackets. The Bolt provided is to clamp the resting section on the J Bracket. The diagonal shaped bolt holes allow height adjustment up to one inch between sections as some lumber varies in size. … Read More
J Bracket Surface Mount 2 PACK #4068A
The Surface Mount J Bracket bolts to the surface of the edge and provides a hook to rest the wood frame. Center bolts to secure the supported frame down are required.
Dock Cleat 8″ Galvanized (2 Pack) #2258
8″ Galvanized Dock Cleat (2 Pack)
Corner Iron 90º #6027A
Corner Iron reinforces the inside corner of the dock frame. Mostly needed on a section that is resting on the J-Brackets for stationary docks or to reinforce corners and stringers on floating docks that are under a lot of torque due … Read More
Jack Pole Extension #4000
For Installing Stationary Dock Sections with the leveling winch and pipe foot.
Marine Grade Aluminum with four stainless set screws.
Pipe Puller #4154
Fits on 1.5″ schedule 40 Pipe. Great for twisting pipe to get it out of the ground if stuck. This is also used to screw in the pipe that has an auger on the end. Works Great with our Dock … Read More
Super Driving Cap #7100
Use this to provide a flat surface for pounding the dock legs in with a sledge hammer. This is a wear part and expected to wear out after long use. The cap absorbs the blow from a sledge hammer … Read More
Leveling Winch #9003
Winch mounts to 1.5″ schedule 40 Pipe with a foot on the base.
Large Hook and Lock Dock Corner Brace 90″ #9631
Support the dock pipe leg under water without getting wet to the side of the dock frame using the Hook & Lock Dock Brace with our Trolley and Track system.
Large Hook and Lock Dock X Brace (4′ or 6′ Wide) 90″ #9638
Brace from Pipe to Pipe under water without getting wet using the Hook & Lock Dock Brace and our Salad Tong shaped clamp.
Medium Hook and Lock Dock Corner Brace 75″ #9633
Support the dock pipe leg under water without getting wet to the side of the dock frame using the Hook & Lock Dock Brace with our Trolley and Track system.
Medium Hook and Lock Dock X Brace (4′ or 6′ Wide) 75″ #9639
Brace from Pipe to Pipe under water without getting wet using the Hook & Lock Dock Brace and our Salad Tong shaped clamp.
Mini Hook and Lock Dock Corner Brace 36″ #9637
Support the dock pipe leg under water without getting wet to the side of the dock frame using the Hook & Lock Dock Brace with our Trolley and Track system.
Small Hook and Lock Dock Corner Brace 54″ #9635
Support the dock pipe leg under water without getting wet to the side of the dock frame using the Hook & Lock Dock Brace.
Small Hook and Lock Dock X Brace (4′ Wide) 54″ #9640
Brace from Pipe to Pipe under water without getting wet using the Hook & Lock Dock Brace and our Salad Tong shaped clamp.
